How to Lubricate a WalkingPad C2: Oil Type, Amount & Steps
The C2 is simple to maintain, but the official sources do not give one universal amount. Start with the manual for your exact C2, understand where the 5–10 mL and 1–2-drop instructions differ, and keep oil away from the wrong parts of the machine.
Short answer
Use silicone treadmill lubricant, then follow the C2 manual.
The C2 manual checked here says 5–10 mL each time, below 4 km/h (2.5 mph) for 10–20 seconds, once every three months. A newer general WalkingPad article says 1–2 drops, so do not merge the two source instructions.
Use silicone only
Use a treadmill or walking-pad lubricant permitted by the exact manual. Do not substitute WD-40, cooking oil, or petroleum-based products.
Amount is revision-sensitive
The C2 manual checked here says 5–10 mL; a newer general article says 1–2 drops. Keep those claims separate.
More oil is not safer
The C2 manual warns that too much lubricant can make the belt slip. Stop, wipe excess, and troubleshoot instead of adding more.
Exact C2 baseline
5–10 mL · below 4 km/h · 10–20 seconds · every 3 months
Those four values come from the C2 manual PDF linked below. The PDF is a regional/version-specific manual, so compare its model label with the manual supplied with your unit before treating the numbers as final.
When to pause
Manual, model label, and region must agree.
If your C2 manual gives another amount, run time, or schedule, follow that document or ask WalkingPad support. Do not use a generic “walking pad oil” answer to override a model-specific instruction.
Open WalkingPad supportC2 step-by-step
A short maintenance job with one important fork in the road.
Steps 1–3 and 5–6 follow the C2 manual and supporting WalkingPad maintenance guidance. Step 4 is deliberately explicit about the amount conflict so a general article is not accidentally mixed with a C2 manual.
- 01
Confirm that the machine is a C2
Match the model name on the machine, order, and manual before using a C2-specific amount. Other WalkingPad revisions can publish different instructions.
- 02
Turn it off and unplug the power cord
Do this before putting a hand under the walking belt. The C2 manual starts its lubrication procedure with the machine off and the power cord unplugged.
- 03
Lift the belt enough to reach the underside
Lift the walking belt so the lubricant can reach the belt-and-deck contact area. The C2 manual says to apply silicone oil on the backside of the belt; it does not tell you to remove the motor cover.
- 04
Use one instruction set for your exact manual
The C2 manual PDF checked here specifies 5–10 mL per application. A newer general WalkingPad article says 1–2 drops. Do not combine those amounts; your included C2 manual takes priority for your revision and region.
- 05
Run the empty belt below 4 km/h
Reconnect power only after the belt is back in place. The C2 manual specifies a no-load run below 4 km/h (2.5 mph) for 10–20 seconds to distribute the oil.
- 06
Check the belt and remove excess oil
Watch for slipping, wipe away any oil that reaches the edges or floor, and check that the belt remains centered. Stop if the belt behaves abnormally instead of adding more oil.
Do not loosen the belt just to oil it. The current general WalkingPad article says lubrication should not require loosening the belt. If the belt is already loose, slipping, or badly misaligned, use the C2 manual's adjustment procedure or contact support instead of improvising tension.
Source conflict, shown plainly
Why does one official page say 5–10 mL and another say 1–2 drops?
These are not interchangeable measurements. The C2 PDF is the only cited source here that names the C2 and provides a C2 maintenance section. The newer article is a general WalkingPad treadmill guide. Treat the exact manual supplied with your machine as the controlling instruction, and contact WalkingPad when your regional documents do not agree.
| Question | Published answer | How to use it | Source |
|---|---|---|---|
| C2 manual amount | 5–10 mL each time | This is the amount printed in the C2 manual PDF used for this page. It is not a universal amount for every WalkingPad model or revision. | C2 manual PDF |
| Current general article | 1–2 drops | WalkingPad’s newer general treadmill article uses this smaller instruction. It is useful context, but it does not identify the C2 revision or replace the included C2 manual. | Current article |
| C2 distribution run | Below 4 km/h / 2.5 mph for 10–20 seconds | This is the C2 manual’s distribution instruction. The newer general article says low speed for a few minutes, so use the exact C2 manual when the two differ. | C2 manual PDF |
| General schedule | C2 manual: once every 3 months | WalkingPad’s collection page gives a broader 3–6 month range for most models. Treat the C2 manual’s three-month line as the model-specific baseline unless your own manual says otherwise. | WalkingPad article |
Choosing the oil
Buy the specification, not the word “oil.”
A product can be called lubricant and still be intended for a different mechanism. Look for silicone-based treadmill or walking-pad language, keep the label, and check the exact C2 manual before applying it.
Official regional product
KingSmith WalkingPad Silicone Oil
The official Netherlands store describes this silicone oil for KingSmith WalkingPad care. It is not evidence of US stock or shipping; confirm your region at checkout.
Use
- Silicone-based treadmill lubricant.
- A label that matches the exact manual.
- A controlled applicator and a cloth.
Skip
- WD-40, penetrating oil, or petroleum products.
- Cooking oil or an unlabelled household oil.
- General-purpose silicone spray unless the manual allows it.
After the application
Use symptoms to stop, not to guess.
Lubrication only addresses the belt-and-deck interface. It does not prove that a noise, error, worn belt, or electrical fault is an oil problem.
The belt slips after oiling
Too much lubricant is one possibility, and the C2 manual explicitly warns that too much can make the belt slip. Turn the unit off, unplug it, wipe excess oil from accessible edges and the floor, and do not keep adding oil. If slipping continues, follow the manual’s belt-adjustment procedure or contact WalkingPad support.
The belt drifts to one side
Lubrication should not be used as a reason to loosen the belt. Check that the belt is centered after the procedure. If it needs adjustment, use the small, equal adjustments and the run-and-check sequence in the exact C2 manual rather than guessing from a different model.
The noise remains after lubrication
More oil is not automatically the answer. Check for visible debris, belt alignment, and obvious slipping. A persistent scrape, grinding sound, error light, or electrical smell is a stop-and-support situation, not a cue to spray oil into the machine.
You cannot tell which oil you have
Pause until the label identifies a silicone-based treadmill or walking-pad lubricant and the exact manual allows it. Do not substitute cooking oil, WD-40, petroleum-based lubricant, or a general household spray.
Purchase and maintenance boundary
If the C2 label and manual do not agree, buy neither the oil nor a replacement part until support confirms the revision.
Send WalkingPad the model/version, region, order information, and a description of the symptom. The manufacturer—not WorkChoose—controls the applicable maintenance and warranty instruction.
FAQ
WalkingPad C2 oil questions, answered with source boundaries
What lubricant should I use on a WalkingPad C2?
Use a silicone-based treadmill or walking-pad lubricant that is permitted by the manual for your exact C2 revision. WalkingPad’s official sources describe silicone oil, and the current general article says to use a non-petroleum silicone-based lubricant. The official KingSmith WalkingPad Silicone Oil product page is a regional storefront; confirm availability and shipping for your country before ordering.
How much lubricant does a WalkingPad C2 need?
The C2 manual PDF checked for this guide specifies 5–10 mL per application and warns that too much can make the belt slip. A newer general WalkingPad article says 1–2 drops. Because those official instructions conflict and the newer article is not C2-revision-specific, do not convert drops to milliliters or combine both instructions: follow the manual that came with your C2, and ask WalkingPad when your regional manual differs.
How often should I lubricate a WalkingPad C2?
The C2 manual says to apply silicone oil once every three months. WalkingPad’s broader collection guidance says most models may fall in a 3–6 month range depending on use. Use the C2 manual’s three-month line as the starting schedule unless the manual supplied with your regional/version-specific machine says otherwise; a dry or rough deck check can help decide whether to postpone, but it does not override the manual.
Where do I put the oil on a WalkingPad C2?
After turning the C2 off and unplugging it, lift the walking belt enough to reach the belt-and-deck contact area. The C2 manual specifically says to apply silicone oil on the backside of the belt. Do not pour oil onto the visible walking surface, spray into electronics, or remove covers unless your exact manual instructs you to do so.
How long should I run the WalkingPad C2 after lubricating it?
The C2 manual specifies running the machine below 4 km/h (2.5 mph) for 10–20 seconds after applying lubricant. WalkingPad’s general article gives a different low-speed duration, so use the C2 manual for your revision. Run it empty first and observe the belt for slipping or tracking problems.
Can I use WD-40, cooking oil, or regular silicone spray?
Do not use them as a substitute for treadmill lubricant. WalkingPad’s current lubrication article warns against WD-40, vegetable oil, and general-purpose silicone sprays, and recommends a non-petroleum silicone-based treadmill lubricant. Keep the product label and your C2 manual together when choosing an oil.
Does the US WalkingPad C2 box include lubricant?
The current US C2 product page lists the machine, power cord, remote, wristband, wrench, and user manual in its package contents; it does not list lubricant there. Regional pages can list different package contents. Do not assume that an oil bottle is included—check your order and region, then buy a compatible silicone treadmill lubricant if needed.
Should I lubricate the C2 if it is still slipping or making a grinding noise?
Not blindly. Excess oil can cause slipping, and persistent grinding, an error light, electrical smell, or abnormal movement needs a stop-and-support response. Check the belt and surface only with the machine unplugged, follow the exact C2 troubleshooting instructions, and contact WalkingPad if the issue remains.
Is this WalkingPad C2 lubrication guide based on a personal test?
No. WorkChoose did not personally lubricate or measure a C2 for this page. The steps and amounts are separated into manufacturer-published instructions, with the conflict between the C2 manual and the newer general article shown explicitly. Product condition and regional instructions can differ.
Are the product links on this page affiliate links?
No. At the time of this review, the links go directly to WalkingPad or its official regional storefront and no affiliate tracking is active on this page. Availability, regional shipping, package contents, prices, and product terms can change.
Continue the fit check
Maintenance is one part of a C2 work setup.
Safety & maintenance
Use the broader preflight for surfaces, clearance, controls, cleaning, and stop procedures.
Read nextDesk setup guide
Measure the floor, desk, monitor, keyboard, cables, and walking zone before working while walking.
Read nextC2 replacement remote
Check the exact remote selector, pairing path, battery, and regional compatibility evidence.
Read nextC2 belt adjustment
Separate left drift, right drift, and slipping before using the model-specific screw direction and empty-belt check.
Read nextMain walking-pad guide
Compare current models by belt fit, desk clearance, controls, storage, and manufacturer evidence.
Read nextWalkingPad Z1 vs C2
See the C2 against Z1 on current size, weight, control, storage, and evidence boundaries.
Read nextOfficial source trail
Recheck the exact C2 manual and regional storefront before applying oil.
Source boundary: WalkingPad US product text, the WalkingPad C2 PDF manual, and WalkingPad/KingSmith lubrication pages checked September 3, 2026. The C2 PDF is a regional/version-specific document; the general article is not a C2 replacement manual. WorkChoose did not make a personal test or a universal compatibility promise. Package contents, oil availability, specifications, prices, warranty terms, and instructions can change.